Protectowire 2000 FireSystem Especificaciones descargar pdf (Pagina 31)

~ 28 ~

System control switches, lamp

indicators and signal monitoring

are managed with this module.

Plug-in design allows for quick

replacement during field repair.

Used in conjunction with the

Main Board (MB-91A).

Standard control card module is

designated as CC-91ANT. This

card eliminates the possibility of

accidental releasing by remov-

ing the “SYS. TEST” button.

&&""%(#&&(%,)/)*#)%$"/

?>DB?<1B4#?4E<5

9C@<1I

&1>5<

The Control Card CC-91A provides system control and indicators for the FS2000 Series system. This card plugs into

the Main Board MB-91A/M printed circuit board left side card slot.

>4931D?BC

 E=@5B)5DD9>7C

?>DB?<)G9D385C

N,1B91D9?>C

CC-91A Control card module with “SYS.TEST” switch. This card must be specifically requested at time of purchase

CC-91ANT No test switch control card module: For use with releasing system where test feature is not desired (Standard)

CC-91AI Intrinsic control card module: For use with intrinsically safe detection circuits (Reference Option H)

CC-91AINT Intrinsic, no test control card: For use with releasing system where test feature is not desired & intrinsically safe circuits (Opt H)

SYS. TEST

System test button: Press and hold for a minimum of 3 seconds. Simulates ALARM condition in all detection

and supervisory zones. (Only available when specified on systems without solenoid release) *See warning

SYS. RESET System Reset button: Press to reset system from ALARM condition.

AL. SIL Alarm Silence button: Press to silenceAlarm Notification Appliance devices activated by ALARM condition

SUP./TRO.

SIL.

Trouble/Supervisory alarm silence button: Press to silence activated common trouble signal (pulsing buzzer) or supervisory

alarm signal (steady buzzer)

LAMP/TRO.

TEST

Lamp and trouble test button: Press to test lamp indicators and system trouble signaling

*Warning: Disconnect all releasing devices and/or equipment shutdown prior to testing system. See Testing & Maintenance section

GFJ

Placed across GFH terminals 1 & 2 to enable ground fault detection. Jumper removed ONLY when diode shunt type intrinsic

safety barriers are employed

ASJ & TSJ

Jumpers are installed when option Z is part of panel design. These jumpers allow the Alarm (ASJ) and Trouble (TSJ) signals to

be silenced.

BT2J

Allows the common trouble output drive to be either Silenceable or Non-Silenceable. To conserve battery power

this jumper is typically installed in the Non-Silenceable position.

AC ON Green AC Power indicator: ON when panel AC voltage is present

SYSTEM ALARM Red System alarm indicator: Activated when any zone ALARM occurs

SYSTEM TROUBLE/

SUP.

Yellow

System trouble indicator: Flashing when system TROUBLE exists. Steady when system

SUPERVISORY ALARM condition exists

ALARM SIL. Yellow Alarm silenced indicator: Flashing when Alarm Notification Appliance circuits are silenced.

ALARM OPEN Yellow Alarm notification appliance circuit OPEN indicator: ON when OPEN exists in circuit.

ALARM SHORT Yellow Alarm notification appliance circuit SHORT indicator: ON when SHORT exists in circuit.

BATTERY LOW Yellow Battery low indicator: ON when battery voltage level is below allowed minimum.

BATTERY OUT Yellow Battery out indicator: ON when battery disconnect or above normal operating voltage below

GND. FAULT Yellow

System ground fault indicator: ON when undesirable positive or negative current leakage occurs

to grd from DC power supply of system. Not available with intrinsic safety barriers (Option H)



1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 62 63

Comentarios a estos manuales

Sin comentarios

Protectowire 2000 FireSystem Especificaciones Pagina 31

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Protectowire 2000 FireSystem