Protectowire 2000 FireSystem Especificaciones descargar pdf (Pagina 7)

))5B95C9B55D53D9?>

5<E75&B513D9?>?>DB?<&1>5<>6?B=1D9?>1>4)@5396931D9?>C

The FS2000 Series of multiple zone fire protection panels is the latest in fire protection from The Protectowire Company, Inc. The

standard model provides, as a minimum, 2 (Class A or B) initiating device circuits and the following standard features:

- Expandable (in multiples of two zones) - Ground Fault Detection (not applicable to all systems)

- Two Supervised Notification

Appliance Circuits - Alarm Lock-in until Reset

- On Board Audible Indicator Silencing - On Board System Reset Button

- Lamp and System Trouble Circuit Test - Dry Alarm and Trouble Contacts

- Initiating Device (Detection) Circuit -IDC- ALARM Test

- Monitors up to 5,000 ft. (1,524 meters) of PROTECTOWIRE Linear Heat Detector Cable per circuit

- Any combination of normally open contact devices

- Accommodates up to (30) NS-series #SLR-24, #SIJ-24, #SLR-24H, Detector Identifier - HD-3

Smoke Detectors (per circuit).

- Battery Monitoring, Low or Out of operating specs. (or disconnected)

)ICD5=)@5396931D9?>C

$?D96931D9?>@@<91>359B3E9DC

Note: Circuits do NOT generate a temporal pattern signal. Appliances that can generate a temporal pattern must be employed

when a temporal pattern is required. Reference DS-9066 in this manual for compatible devices.

~ 4~

&B9=1BI&?G5B

120VAC 50/60Hz 1.75 amp maximum ** see below

)E@@?BD54)D1>42I1DD5B95C

24VDC 4.5AH minimum to 60AH maximum * see below

1DD5BI81B75B

27VDC 1.25 Fast charge, 27.6mA Max trickle charge, 12mA (typical)

&B9=1BI)ICD5=&?G5B

24V FWR by T1, 175VA typical. Greater VA rating as required by system

)ICD5=(57E<1D54&?G5B

MB and EB type boards provide 12 & 24VDC regulation. RS type boards

provide24VDC regulation only

?==?><1B=?>D13DC

3 amps @ 30VDC, resistive load, silenceable

?==?>*B?E2<5?>D13DC

1 amp @ 24VDC, resistive load, factory preset as non-silenceable

?==?>)E@5BF9C?BI?>D13DC

1 amp @ 24VDC, resistive load, programable

?EBG9B545D53D?B@?G5B

24VDC @ 200mA Max. used for Special Application

(non-supervised, for supervision use PSR-2040)

>F9B?>=5>D1<?@5B1D9>7

3?>49D9?>C

Ambient temperatures: 32 - 120 degree F (0 - 49 degrees C)

Humidity: Max. 95% relative non-condensing

*Battery requirements calculated per individual system demands. (See battery selection data)

**240VAC 50/60 Hz 0.85amp maximum also available. Check installation wiring diagram (IWD).

,?<D175

24 V Full wave rectified (FWR) with battery standby.

EBB5>D

Two amps per circuit three amps maximum combined

Maximum two conductor copper feed cable resistance may not exceed 1 ohm (see below

1.4 Volts Maximum Line Loss

-

Maximum of 500’ (feet)

-

Maximum of 300’ (feet)

N-

Maximum of 200’ (feet)

Note: Notification Appliance Circuits current rating may be reduced depending on

each systems current requirements. Reference the installation wiring diagram (IWD)

for individual systems actual ratings. Reference DS-9066 for more information

1 2 3 4 5 6 7 8 9 10 11 12 ... 62 63

Comentarios a estos manuales

Sin comentarios

Protectowire 2000 FireSystem Especificaciones Pagina 7

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Protectowire 2000 FireSystem